Spare parts ECM Casa V
On this page you will find parts specific to the ECM Casa V. This series from ECM Heidelberg is made by ECM itself in Germany and has a single boiler on top of the group. The Casa V is a further development of the Casa and has a rotary knob for the steam.
The filters can be found on this page and for the filter holder on this page.
Spring filterholder 58mmFor all machines with a 58mm filter (inner diameter = tamper diameter)
Replace this spring when your filters fall out the portafilter.
For E61 machines, Bezzera BZ series, QuickMill, Rancilio, Gaggia, Vibiemme, Marzocco, Cimbali…€ 0,75
Gasket teflon steam pipe - steam tap universalTeflon gasket between the nut of the knee joint of the steam/water pipe and the steam tap. There is also a o-ring available.
16 X 2 MM€ 0,95
Pump suport Ulka€ 1,25
Rubber steampipe 10mmPrevent burnt fingers with this rubber cover for the steam pipe. For steam pipe with an outer diameter of 10 mm, tip for assembly: use a little bit of washing-up liquid so that the cover easily goes over the thickening of the…
€ 1,25
- O-ring water tank ECM
O-ring for the water tank connection of ECM Mechanika/Technika III and IV machines.
9,92X2,62MM OR112
B7496073€ 1,50 
O-ring disk ECM Botticelli & Casa- ECM Botticelli & Casa
- Profitec PRO300
- Rocket Boxer & R9C449900790
+/- 47,3x2,62 mm€ 2,00
Switch 4 polesUniversal switch, used by many brands and models, including Ascaso Steel, La Piccola Sara, ECM, Vibiemme, Isomac, Quick Mill etc.
Suitable for both round and oval supports. We recommend replacing the support if you swap the…€ 3,95
Filterholder gasket E61 8mm€ 4,95
Pump self-priming bypassUsed in many espresso machines to drain off the air. Self-priming in counter pressure conditions.
Also available in a higher quality brass version.
Assemble with Loxeal or PTFE Tape or with an o-ring.
1/8m x 1/8f€ 4,95
Boiler gasket ECM Casa IV€ 5,95
Group gasket E61 8,5mm SiliconeSilicone piston ring, stronger material than the standard piston ring. For use in the brew group of a wide variety of E61 machines.
We use 8.5mm as standard in most brands; especially when using a silicone ring, 8.5mm is…€ 6,95
Shower holder E61 ring groupexternal ø 58.5 mm - height 7.5 mm - hole ø 6.5 mm
made of brass CW510L (OT57) C529900550€ 12,95
Shower E61 ring group CI 200 IM competition styleIMS is the standard for barista's that participate at competition level. The surface is extremely smooth and the holes are perfectly distributed. An improved water distribution so you get an even better extraction.
You can now…€ 16,50
Solenoid Parker Valve ZB09 9WL33,9xH32,8xP43,4mm
Diameter hole 14,2mm
PARKER SOLENOID VALVE COIL 230VAC 50/60Hz ZB09 9W IP65€ 29,50-14%
Pump Ulka EX5 230 Volt€ 34,95 € 29,95
Naked filterholder E61Get the best shots from your espresso machine with this naked filterholder (open filter holder) Use this in combination with the standard supplied 21 gram filter and see how the crema comes out the filter. In addition, the naked…
€ 31,95
Valve 3 way base ParkerVE128IR - drain ø 1/8" conical - max 20 bar
CW617N (OT58)
RUBY seal - orifice ø 1,3 mm
fluid temperature -30°C+140°CTo be used in combination with 9 watt Parker solenoid coils
Base: 32x32mm
Height: 67 mm€ 39,95
