Spare parts ECM Mechanika/Technika IV
On this page you will find parts specifically for the ECM Mechanika/Technika IV with vibration pump. This series of ECM Heidelberg is made by ECM itself in Germany and has some different parts than its predecessors. There is also a Mechanika/Technika IV Profi series, which is completely different, look here for the parts.
The version with a vibration pump (2009-2018) has a copper boiler (the Profi version has a stainless steel boiler and rotary pump). The IV can be equipped with a steam/tea tap with rotary knob or a push tap. (Profi always push)
All parts for the E61 group can be found on this page, the filters on this page and for the filter holder on this page.
Gasket teflon steam pipe - steam tap universalTeflon gasket between the nut of the knee joint of the steam/water pipe and the steam tap. There is also a o-ring available.
16 X 2 MM€ 0,95
O-ring Steampipe ECM Profi€ 1,00
Rubber steampipe 10mmPrevent burnt fingers with this rubber cover for the steam pipe. For steam pipe with an outer diameter of 10 mm, tip for assembly: use a little bit of washing-up liquid so that the cover easily goes over the thickening of the…
€ 1,25- O-ring water tank ECM
O-ring for the water tank connection of ECM Mechanika/Technika III and IV machines.
9,92X2,62MM OR112
B7496073€ 1,50 
- O-ring spindle steam tap ECM IV (set of 2)
For ECM Classika II and Technika/Mechanika IV spindles
Set of 2
OR112 9.92x2.62€ 1,95 - O-ring spindle steam tap ECM profi (set of 2)
For ECM Profi (push and go / lever handles)
Set of 2€ 1,95 
Closing gasket spindle ECM IVFor Mechanika/Technika IV and Classica II (not profi quick steam tap)
9 x 6,5 mm€ 3,45
Pump self-priming bypassUsed in many espresso machines to drain off the air. Self-priming in counter pressure conditions.
Also available in a higher quality brass version.
Assemble with Loxeal or PTFE Tape or with an o-ring.
1/8m x 1/8f€ 4,95
Group gasket E61 8,5mm SiliconeSilicone group gasket, longer lasting material than the standard gasket.
For the brewing group of very many different machines: Including everything with an E61 brew group: ECM, Faema, Rocket, Vibiemme, Wega, Bezerra, Kees van…€ 6,95
Thermostat 135 degrees RESETABLEM4 thread, manual resettable.
ECM & Rocket C199901550
ECM Heidelberg B7434009
BZ 7434009€ 6,95
Empty valve 1/4 low€ 7,95
Pipe manometer 1/8F x 1/8F 120 cmPipe for manometers. 120cm, extra long so that it better dampens the vibration of the pump. Adaptable to any situation. (additional roll-up or un-roll)
2x 1/8F€ 7,95
Level probe boiler 120mmThe boiler level probe is an essential part for a heat exchanger machine, when the insulation it is no longer good there is a risk that the heating element will come above the water level in the boiler. The probe must also be…
€ 9,95
Safety valve E61 boiler 3/83/8 bsp (16.66mm)
2,0 bar max, suitalbe for all espressomachines€ 11,95
Collector watertank ECMECM HEIDELBERG: ELEKTRONIKA II PROFI, ELEKTRONIKA PROFI, MECHANIKA, SYNCHRONIKA, TECHNIKA/MECHANIKA IV & V, CLASSICA II/PID, CASA V.
PROFITEC: PRO300, PRO500, PRO600, PRO700, PRO800
P6020.K4€ 12,95
Lever switch 4 poles 15 A4 poles 15 amp
For Vibiemme, Isomac, Ascaso, QuickMill 3000, Francis Francis, BFC Junior, Bezzera and many others€ 13,25
Float watertank ECMECM HEIDELBERG: ELEKTRONIKA II PROFI, ELEKTRONIKA PROFI, MECHANIKA, SYNCHRONIKA, TECHNIKA/MECHANIKA IV & V, CLASSICA II/PID, CASA V.
PROFITEC: PRO300, PRO500, PRO600, PRO700, PRO800
P6021€ 14,50
Pressure switch 16 ampère 1/4Thread 1/4.
PRESSURE SWITCH XP110 0,5-1,5 BAR G1/4
Adjust. press. range 0,5-1,5 BAR, pre-adjust. 1 Bar. 125°C, G1/4, 16A 250VAC.
There is also a more solid alternative€ 19,95
Naked filterholder E61Get the best shots from your espresso machine with this naked filterholder (open filter holder) Use this in combination with the standard supplied 21 gram filter and see how the crema comes out the filter. In addition, the naked…
€ 29,95-14%
Pump Ulka EX5 230volt€ 34,95 € 29,95
Heating element 1" 1350 watt with gasketThread:1" bsp (+/- 33,3 mm)
Length: 125 mm
220 volt 1350 watt
Heating element for many brands:
ECM and Rocket (not for ECM Mechanica 3, this model has a metric thread (32mm)
Isomac HX machines
Vibiemme Domobar…€ 36,50-28%
Overhaul kit E61 brew group (complete)Kit for complete overhaul E61 brew group:
∙ Shower standard, Shower IMS IM200 or Shower IMS Matrix
∙ Supplement 0,5mm
∙ Group gasket 8mm standard or group gasket 8,5mm silicone
∙ Ring 1
∙ Ring 2 3x
∙ Ring 3
∙ O-ring…€ 89,95 € 64,95
Controlbox / box Gicar 9.9.06.30G 01ECICM2004
Gicar 9.9.06.30G 01
ECM Technika/Mechanika 4 / Pavoni Giotto€ 139,95
