Spare parts Bezzera Mitica

This O-ring fits the fitting for the push tap of Bezzera. (Gasket between front panel and tap)

OR0114

All Bezzera models from 29/01/2014r29/01/2014

7496052

OR between the nut of the knee joint of the steam/water pipe and the steam tap. There is also a teflon gasket available.

16 X 2 MM

For all machines with a 58mm filter (inner diameter = tamper diameter)

Replace this spring when your filters fall out the portafilter.

For E61 machines, Bezzera BZ series, QuickMill, Rancilio, Gaggia, Vibiemme, Marzocco, Cimbali…

This ring is located at the bottom of the nut of the connection of the steam tap and fits in with many models of espresso machines. If the steam or water pipe moves stiffly, or if it leaks at the knee joint, replace this ring. We…

Angled coupling for an Ulka pump or output of a solenoid valve or OPV.

Lelit MC017

QuickMill GO3000PG

Prevent burnt fingers with this rubber cover for the steam pipe. For steam pipe with an outer diameter of 10 mm, tip for assembly: use a little bit of washing-up liquid so that the cover easily goes over the thickening of the…

With this special Molicote paste you lubricate your filter holder and group. Put the past under the ears of the filter holder and then you turn the filter holder into the brew group so that paste also comes in the tread. The paste…

OR112 for Bezzera water tanks

For Bezzera taps with quick/push steam tap

11x4x4

BZ 5496042

Closing gasket for adjustable overpressure valve Bezzera.

11 x 3 mm

BE 5493042

For Bezzera E61 machines > 30-10-2012

For Bezzera BZseries machines > 19-03-2013

If you choose several meters, we will deliver that as in 1 piece. For example, 3x1 meter is supplied as a piece of 3 meter

CONICAL SEAL ø 12x5x6 mm

BZ 5494004

Y connector for silicone hose. 5mm

Also available in a more solid brass version.

Bezzera 7303033

∙ BZ07
∙ BZ09
∙ BZ10
∙ Galatea Domus
∙ Giulia
∙ Hobby
∙ Unica

Lelit MC532

Closing gasket for adjustable overpressure valve of Bezzera.

8 x 4 mm

BE 5493001

For Bezzera E61 machines up to 30-10-2012

For Bezzera BZseries machines up to 19-03-2013

Filter for water tank ECM Mechanika/Technika III and Bezzera

1/4f

7374002

Used in many espresso machines to drain off the air. Self-priming in counter pressure conditions.

Also available in a higher quality brass version.

Assemble with Loxeal or PTFE Tape or with an o-ring.

1/8m x 1/8f

7633624 BEZZERA

Head ø 13.4 mm - hole ø 10 mm

7633625 BEZZERA

Head ø 13.4 mm - hole ø 10 mm

7633622 BEZZERA

ECM CLASSIKA II - ELEKTRONIKA II PROFI - MECHANIKA

7633621 BEZZERA

ECM CLASSIKA II - ELEKTRONIKA II PROFI - MECHANIKA

Protector for lever switch,

BZ 7372507

ECM B7372507

27,5mm for all modern E61 brew heads

Silicone group gasket, longer lasting material than the standard gasket.

For the brewing group of very many different machines: Including everything with an E61 brew group: ECM, Faema, Rocket, Vibiemme, Wega, Bezerra, Kees van…

M4 thread, manual resettable.

ECM & Rocket C199901550

ECM Heidelberg B7434009

BZ 7434009

12mm guide, for all E61 brew groups

1/4 bsp (13,16mm) suitable for all espressomachines

Beautiful elegant button for the control lever of your E61 brew group and/or for the levers of the lever tap (m8)

M14x M13

Bezzera code: 5225416TP

Upper guide: 13mm

Lower guide: 26,5mm

Total length: 53mm

For all modern E61 brew heads, except Vibiemme

The boiler level probe is an essential part for a heat exchanger machine, when the insulation it is no longer good there is a risk that the heating element will come above the water level in the boiler. The probe must also be…

nut ø 3/8 "F - height 18 mm - body ø 22 mm

5222823CM

4 poles 15 amp

For Vibiemme, Isomac, Ascaso, QuickMill 3000, Francis Francis, BFC Junior, Bezzera and many others

For all modern E61 brew groups

overall length 47.5 mm
threaded pin M4
head ø 12x5 mmBZ 5260204DL

IMS is the standard for baristas that participate at competition level. You can now also place this shower in your E61 brew group. The surface is extremely smooth and the holes are perfectly distributed. An improved water…

Thread 1/4.

PRESSURE SWITCH XP110 0,5-1,5 BAR G1/4

Adjust. press. range 0,5-1,5 BAR, pre-adjust. 1 Bar. 125°C, G1/4, 16A 250VAC.

There is also a more solid alternative

Upgrade your E61 brew group with this beautifull manometer. You can use the m6 tread on the front of you group, use tape of loxeal to avoid leaking. Ideal for espresso machines without a pump pressure manometer.

5530011

Pay…

Bezzera E61 models and ECM Mechanika/Technika III

5225228 and 7826206

2x 1/8 bsp F

220/230v

Upgrade your E61 brew group with this beautifull manometer. You can use the m6 tread on the front of you group, use tape of loxeal to avoid leaking. Ideal for espresso machines without a pump pressure manometer.

5530011

Pay…

Bezzera BZ07, BZ09, BZ10, BZ13, BZ16,BZ40, GIULIA, MAGICA, MITICA, STREGA, UNICA

M12 bold

5978508 BEZZERA
5978508.01 BEZZERA

Bezzera E61 or ECM Mechanika/Technika III espressomachine.

5162233LL

Get the best shots from your espresso machine with this naked filterholder (open filter holder) Use this in combination with the standard supplied 21 gram filter and see how the crema comes out the filter. In addition, the naked…

Probe ø 6x25 mm - Thread ø 1/4"M bsp

For Bezzera, Izzo/myWay, Rocket, ECM, San Remo, Lelit ea.

A199904679 Rocket
ELETSONTEMPII Vibiemme (VBM)
ELETSONTEMPPI Vibiemme (VBM)

The MATRIX® shower is made of 316L s.steel plate, composed of 50 layers of micro pheres, creating tens of thousand of routes, as narrow as 4-5 microns. This allows a homogeneous distribution of the water on the coffee disk. The…

Thread: 32 x 1,5 mm
Length: 160 mm
220/240 volt

1250/1450 watt

For Bezzera E61 and BZ machines and ECM Technika/Mechanika 3

Bezzera code 5722240TP

OPV and non return valve included, for Bezzera and ECM 3rd generation

5965212.01AL

CE -UL Approv. 3 poles. Male thread G 1/4 for pipe d.4x6 mm, adjust. pressure range 0,5 ÷ 1,4 bar, max breaking capacity: 20A – 400V a.c. (AC1)

P303/T01

For Bezzera Magica, Mitica, Strega and other E61 models. Also suitable for ECM machines made by Bezzera

5329020DC-AL

connection ø 1 "M
3 connections ø 1/8 "F
immersion depth 147 mm
overall length 158 mm
brass body ø 28 mm

This allows you to convert your Bezzera from the normal steam / water taps to the so-called push taps. By operating the levers you immediately have water or steam.

Gicar code 9..3.00.61G02

Bezzera code 7434017

220volt

60mm

ECICB7661034.0

BZ 7661034.01

Gicar 9.1.24.20G

RL30/4ESS/F

ECM Technika/Mechanika 3 and Bezzera machines

Bezzera Magica, Mitica, Strega and other Bezzera E61 machines

5320501.02BL