Spare parts ECM Mechanika/Technika IV Profi
On this page you will find parts specifically for the ECM Mechanika/Technika IV Profi. This series of ECM Heidelberg is made by ECM itself in Germany and has some different parts than its predecessors.
There is also a standard Mechanika/Technika IV series (not Profi), which is completely different, look here for the parts. The version with a vibration pump has a copper boiler, the Profi version has a stainless steel boiler and rotary pump. The IV Profi is always equipped with a steam/tea tap with push control.
All parts for the E61 group can be found on this page, the filters on this page and for the filter holder on this page.
Gasket teflon steam pipe - steam tap universalTeflon gasket between the nut of the knee joint of the steam/water pipe and the steam tap. There is also a o-ring available.
16 X 2 MM€ 0,95
O-ring steampipe universalThis ring is located at the bottom of the nut of the connection of the steam tap and fits in with many models of espresso machines. If the steam or water pipe moves stiffly, or if it leaks at the knee joint, replace this ring. We…
€ 0,95
O-ring Steampipe ECM Profi€ 1,00
Rubber steampipe 10mmPrevent burnt fingers with this rubber cover for the steam pipe. For steam pipe with an outer diameter of 10 mm, tip for assembly: use a little bit of washing-up liquid so that the cover easily goes over the thickening of the…
€ 1,25
- O-ring water tank ECM
O-ring for the water tank connection of ECM Mechanika/Technika III and IV machines.
9,92X2,62MM OR112
B7496073€ 1,50 - O-ring spindle steam tap ECM profi (set of 2)
For ECM Profi (push and go / lever handles)
Set of 2€ 1,95 
Rubber lever rod ECM (set of 3)Rubbers for the lever rod of the ECM Heidelberg machines with E61 brewing group.
We supply this article as a set of 3. We advise to lubricate the rubbers well with a heat-resistant silicone or PTFE grease for a smooth operation…€ 2,85
Gasket for heating element ECM V2Gasket for the ECM RVS boilers of among others Casa,Technika en Mechanika IV,
€ 4,95
Group gasket E61 8,5mm SiliconeSilicone group gasket, longer lasting material than the standard gasket.
For the brewing group of very many different machines: Including everything with an E61 brew group: ECM, Faema, Rocket, Vibiemme, Wega, Bezerra, Kees van…€ 6,95
Thermostat 135°C. RESETTABLEM4 thread, manual resettable.
ECM & Rocket C199901550
ECM Heidelberg B7434009
BZ 7434009€ 6,95
Empty valve 1/4 low€ 7,95
Pipe manometer 1/8" F x 1/8" F, L=120 cmPipe for manometers. 120cm, extra long so that it better dampens the vibration of the pump. Adaptable to any situation. (additional roll-up or un-roll)
2 x 1/8" F€ 7,95
Non-retour valve 1/8 M x 1/8 MThis valve prevents water from flowing back from, for example, the boiler or heat exchanger.
Non-return valve for use in an HX machine.
Connection: 2 x 1/8" BSP male
Length: 47.5mm including thread, 33mm without€ 8,95
Level probe boiler 120mmThe boiler level probe is an essential part for a heat exchanger machine, when the insulation it is no longer good there is a risk that the heating element will come above the water level in the boiler. The probe must also be…
€ 9,95
Safety valve E61 boiler 3/83/8 bsp (16.66mm)
2,0 bar max, suitalbe for all espressomachines€ 11,95
Lever switch 4 poles 15 A4 poles 15 amp
For Vibiemme, Isomac, Ascaso, QuickMill 3000, Francis Francis, BFC Junior, Bezzera and many others€ 13,75
Collector watertank ECMECM HEIDELBERG: ELEKTRONIKA II PROFI, ELEKTRONIKA PROFI, MECHANIKA, SYNCHRONIKA, TECHNIKA/MECHANIKA IV & V, CLASSICA II/PID, CASA V.
PROFITEC: PRO300, PRO500, PRO600, PRO700, PRO800
P6020.K4€ 13,95
Float watertank ECMECM HEIDELBERG: ELEKTRONIKA II PROFI, ELEKTRONIKA PROFI, MECHANIKA, SYNCHRONIKA, TECHNIKA/MECHANIKA IV & V, CLASSICA II/PID, CASA V.
PROFITEC: PRO300, PRO500, PRO600, PRO700, PRO800
P6021€ 14,95
Manometer E61 brew group WhiteUpgrade your E61 brew group with this beautifull manometer. You can use the m6 tread on the front of you group, use tape of loxeal to avoid leaking. Ideal for espresso machines without a pump pressure manometer.
5530011
Pay…€ 21,95
Manometer E61 brew group BlackUpgrade your E61 brew group with this beautifull manometer. You can use the m6 tread on the front of you group, use tape of loxeal to avoid leaking. Ideal for espresso machines without a pump pressure manometer.
5530011
Pay…€ 24,95
Naked filterholder E61Get the best shots from your espresso machine with this naked filterholder (open filter holder) Use this in combination with the standard supplied 21 gram filter and see how the crema comes out the filter. In addition, the naked…
€ 31,95
Solid state relais 25amp 220/9-18VDCRelais for Lelit machines with 12 volt PID system.
25 amp
1 fase 220-240V 9-18VDC€ 43,95
Solid state relay 25amp 220/4-32VDC25 amp
1 fase 220-240V 94-32VDC
ECM/Profitec P.6031
Rocket A190004666€ 45,95
Heating element ECM V2 incl gasketFor ECM Inox boilers of Casa,Technika en Mechanika IV,
1400 watt 230volt inc gasket
87 mm - 2 poleb
distance between the holes 58 mm
flange ø 54 mm€ 64,95-26%
Overhaul kit E61 brew group (complete)Kit for complete overhaul E61 brew group:
∙ Shower standard, Shower IMS IM200 or Shower IMS Matrix
∙ Supplement 0,5mm
∙ Group gasket 8mm standard or group gasket 8,5mm silicone
∙ Ring 1
∙ Ring 2 3x
∙ Ring 3
∙ O-ring…€ 89,95 € 66,95
Pump professional "Rotary vane 100 lt/h" compactCompact pump for installation in semi-professional espresso machines.
Yield 100 lt/h.
To be mounted on the motor with the supplied clamp, pressure adjustable.
Length from pump 60mm
We call this a Procon pump, because this is…€ 94,95
Controlbox / box Gicar 9.9.06.30G 01ECICM2004
Gicar 9.9.06.30G 01
ECM Technika/Mechanika 4 / Pavoni Giotto€ 139,95
